This specification covers the chemical, mechanical, and dimensional requirements, and associated test methods for straight and bent, headed and headless anchor bolts (also known as anchor rods) made of carbon, carbon boron, alloy, or high-strength low-alloy steel and having specified yield strengths. The anchor bolts are furnished in three strength grades, two thread classes, and various sizes, and are intended for anchoring structural supports to concrete foundations such as building columns, column supports for highway signs, street lighting and traffic signals, steel bearing plates, and similar applications. This specification, however, does not cover the requirements for mechanical expansion anchors, powder-activated nails or studs, and anchor bolts fabricated from deformed bars. The bolts shall adhere to specified elemental chemical compositions as examined by heat and product analysis. They shall also be tested for their conformance with mechanical properties such as tensile strength, yield strength, elongation, reduction of area, and stress area. The anchor bolts shall also meet specified values for nominal size, body diameter, bend section, length, bend angle, and coated length. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers straight and bent, headed and headless, carbon, carbon boron, alloy, or high-strength low-alloy steel anchor bolts (also known as anchor rods). The anchor bolts are furnished in three strength grades, two thread classes, and in the sizes specified in Section 4. 1.2 The anchor bolts are intended for anchoring structural supports to concrete foundations. Such structural supports include building columns, column supports for highway signs, street lighting and traffic signals, steel bearing plates, and similar applications. 1.3 Supplementary requirements are included to provide for Grade 55 weldable steel, permanent manufacturers and grade identification, and impact properties for Grades 55 and 105. 1.4 Zinc coating requirements are included in Section 7 for applications requiring corrosion protection. 1.5 The recommended grade and style of nut and washer are included in 6.6 and 6.7 for each grade. 1.6 This specification does not cover the requirements for mechanical expansion anchors, powder-activated nails or studs, or anchor bolts fabricated from deformed bar. 1.7 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 2. Referenced Documents (purchase separately) ASTM Standards A194/A194M Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both A370 Test Methods and Definitions for Mechanical Testing of Steel Products A563 Specification for Carbon and Alloy Steel Nuts A673/A673M Specification for Sampling Procedure for Impact Testing of Structural Steel A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel D3951 Practice for Commercial Packaging F436 Specification for Hardened Steel Washers F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners Research Council on Structural Connections Standard SpecificationforStru ASME Standards B18.18.2M Inspection and Quality Assurance for High Volume Machine Assembly Fasteners Index Terms anchor bolts; steel; Anchor bolts; Carbon-boron steel; Carbon steel bolting materials specifications; HSLA (high-strength low-alloy) steel specifications; Steel bolting materials specifications; ICS Code ICS Number Code 21.060.10 (Bolts, screws, studs) DOI: 10.1520/F1554-07AE01 ASTM International is a member of CrossRef.
ASTM A490 - 11 Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
1. Scope 1.1 This specification covers two types of quenched and tempered, alloy steel, heavy hex structural bolts having a tensile strength of 150 to 173 ksi. 1.2 These bolts are intended for use in structural connections. These connections are covered under the requirements of the Specification for Structural Joints Using Specification A325 or A490 bolts, approved by the Research Council on Structural Connections; endorsed by the American Institute of Steel Construction and by the...
ASTM A194 / A194M - 11 standard specification for carbon and alloy steel nuts for bolts for high pressure or high temperature service, or both
This specification covers a variety of carbon, alloy, and martensitic and austenitic stainless steel nuts. These nuts are intended for high-pressure or high-temperature service, or both. Bars from which the nuts are made shall be hot-wrought. The material may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be solution annealed or annealed and strain-hardened. Each alloy shall conform to the chemical composition requirements prescribed. Hardness tests,...
ASTM A320 / A320M - 11a standard specification for alloy-steel and stainless steel bolting for low-temperature service
This specification covers alloy steel bolting materials for pressure vessels, valves, flanges, and fittings for low-temperature service. Each alloy shall conform to the prescribed chemical composition requirements. The material, as represented by the tension specimens, shall conform to the requirements as to tensile properties such as tensile strength, yield strength, elongation, and hardness. The material shall meet the prescribed impact energy absorption requirements and the recommended...
Mölnlycke announces partnership with Engie and Veolia to drive sustainable practices in the manufacturing industry
Mölnlycke, a world-leading medical product and solutions company, has announced two landmark partnerships with global sustainability solutions providers Engie and Veolia. Aiming to deliver best-in-class energy-saving and wastewater treatment solutions respectively for its on-going and upcoming projects, the brand strives to build a sustainable healthcare manufacturing ecosystem whilst addressing the market demands for high-quality medical gear. These collaborations are in line with the championed WeCare...
BPC Instruments files additional patent application for its next-generation instruments
BPC Instruments AB (“BPC” or “the Company”) has submitted the third patent application for this year, which covers a novel incubation system for the Company’s next-generation analytical instruments with applications in multiple biotech sectors. With this patentable technology, BPC will offer a unique microbial incubator that not only covers a wide temperature range for various microbial respiration analyses and high user convenience, but also high thermo-efficiency with extremely low...
No comments were found for ASTM F1554 - 07ae1 standard specification for anchor bolts, steel, 36, 55, and 105-ksi yield strength. Be the first to comment!
Environmental XPRT is a global environmental industry marketplace and information resource. Online product catalogs, news, articles, events, publications & more.
Environmental XPRT is part of XPRT Media All Rights Reserved. Terms Privacy
Our sites: Agriculture XPRT Energy XPRT Medical XPRT XPRT